No wireless in Ubuntu 14.04

OK, this is a personal post.

First off, run the following code to find who made the wireless card.
lspci -vnn | grep Network

This page was the most helpful for solving the wireless issue:
https://askubuntu.com/questions/55868/installing-broadcom-wireless-drivers

So with that in mind, the following is what we have right now which is simplified in just 3 steps:

1. Knowing what Broadcom Wireless Card you have

There are dozens of Broadcom wireless cards and more seem to appear every day. The key to finding the correct driver for any network card is what is known as the PCI ID (PCI.ID). To find out which PCI.ID you have, we proceed to opening the terminal by pressing CTRL+ALT+T (It should open a window with a blank background) and inside this terminal we run the following command:

lspci -nn -d 14e4:

You will get something like the following if you have a Broadcom Wireless Adapter (The ID 14e4 used in the example above in most cases is a Broadcom Wireless Card):

Broadcom Corporation BCM4306 802.11bgn Wireless Network Adapter [14e4:4320] (rev 03)

The PCI.ID in this example is 14e4:4320 as seen inside the Brackets […]. In some cases you will also need the revision version (if it appears) for some special cases. In this case, the revision version is rev 03 as shown inside the Parentheses (…) at the end. So what you will need after this search is:

[14e4:4320] (rev 03)

With this new information you can look in the table below and select the appropriate method to install your driver. For example, In this case, since you have the 14e4:4320 rev 03, if we go down the list to the one that shows the exact same PCI.ID you will see that in the columns for Ubuntu 12.04, 13.10 or 14.04 it shows the firmware-b43-installer package driver. This means that you will only have to install this particular package since it appears in all Ubuntu version columns.

NOTE – Before proceeding, if you have previously installed any drivers, have blacklisted or uncommented any driver files or configuration files or have done any changes whatsoever to the system to make the drivers work in previous attempts, you will need to undo them in order to follow this guide. We assume you are doing this from scratch and have not changed any configuration files, modules or drivers in the system in any way (apart from updating the system). This includes any installations using apt-get, aptitude, synaptic, dpkg, software center or manual compilation and installation of the packages. The system has to start from scratch in order for this to work and to avoid any conflicts that may appear if earlier work was done.

For example, if you have previously installed the bcmwl-kernel-source package, you will need to remove it by using the purge method:

sudo apt-get purge bcmwl-kernel-source

2. Preparing the System

If you have just installed Ubuntu, you will need to build an index of available packages before we can install your driver if you have not done so already:

sudo apt update

I would even go so further as to update the Ubuntu list of PCI.IDs:

sudo update-pciids

Just in case the ID of a particular new Broadcom Device you are using has just appeared.

Now using the PCI.ID you found in the steps above, we then search in the list below to find the matching PCI.ID and the method to install the driver associated with it in a simple and correct way. The terminal will be used to avoid any GUI related issues. This applies with all cases, except as noted. The installation procedure is done only via terminal and also while connected to the internet with a temporary wired ethernet connection or USB modem or any means possible that can give your PC, for the time, Internet access. After you find in the list below the correct package we then proceed with the installation.

3. Installing the Package (online)

Assuming you used the PCI.ID 14e4:4320 rev 03 as found in your search above, and then looked at the table below and found that the correct package to install is the firmware-b43-installer, we then proceed to simply install this package in the terminal:

sudo apt install firmware-b43-installer

and then reboot

sudo reboot

The format to install is pretty simple, it’s just:

sudo apt install <PACKAGE_NAME>

In the example above, the PACKAGE_NAME is firmware-b43-installer.

Anyway, that got me back up and running.

Posted 08/10/2018 by lacithedog in Computers, Computing, Linux, Ubuntu, Wireless

%d bloggers like this: